Back to top

1999 Custom 62 Breen Custom Aluminum

Plymouth, Massachusetts

$250,000

Custom Built Fly bridge built from 1/4" 5058 Aluminum plating 5" x 4" 6061 Rib construction 24" on center. 5 Stateroom 3 head layout, Large salon, lower helm and controls on Fly bridge. New twin Lugger -L6140AL2.3 six cylinder diesels with less than 400 hours. Twin Disc MG5114V 1.8:1 Gears w/ 2.75" shafts w/ PSS Dripless shaft seals. 28 Knots WOT.

Basic Boat Info

Price: $250,000
Tax Status: Not Applicable
Boat Name: Charlie's Tuna
Make: Custom
Model: 62 Breen Custom Aluminum
Year: 1999
Condition: Used
Category: Power
Construction: Aluminum
Boat Hull ID: BREEN62001999
Has Hull ID: Yes

Dimensions

Length: 62 ft

Engines / Speed

Engines: 2
Engine #1 Specs:
  • Make: Lugger
  • Model: L-6140AL2.3
  • Drive Type: V
  • Fuel: Diesel
  • Engine Power: 700hp
  • Type: Inboard
  • Propeller Type: 5 Blade, Alloy
  • Year: 2013
  • Engine Hours: 375
  • Engine Location: Port
Engine #2 Specs:
  • Make: Lugger
  • Model: L-6140AL2.3
  • Drive Type: V
  • Fuel: Diesel
  • Engine Power: 700hp
  • Type: Inboard
  • Propeller Type: 5 Blade, Alloy
  • Year: 2013
  • Engine Hours: 375
  • Engine Location: Starboard
Total Engine Power: 1,400hp

Other

Drive Type: V
Boat Class: Flybridge

Contact

Capt. Buck Berry
For more details or questions about other listings please contact Capt. Buck Berry at (781) 834-9790
South Shore Dry Dock Marine, Inc.

Office

South Shore Dry Dock Marine, Inc.
612 Plain Street
Marshfield, Massachusetts, US, 02050
Tel:(781) 834-9790


Builders description

Charlie's Tuna Specifications:

General:

 Year Built: 1999

 Owner/Builder: Charles S. Breen

 Specification Hull:

LOA: 62' 0"

 LWL: 51' 0"

 Beam: 16' 4"

 Draft: 4' 0"

 Displacement: 52,000 lbs (Dry)

Fuel Capacity: 1500 gal.

Hull Plating: .25" 5058 aluminum

 Keel: .5"x 6" 6061 aluminum

 Ribs: .5"x 4" 6061 aluminum (24" oc)

 Stringers: .5" x 1.5" 6061 aluminum (12" oc)

 Transom: .5" 5058 aluminum

 Engine Beds: 3.5"x 8" x .375" 6061 aluminum

Dead Rise: 19 degrees

 Chines: Single 8" hard

 Welding: All seams, triple TIG welded outside, Triple MIG welded inside with matched hull alloy.

Specification Running Gear:

Engines: Twin Lugger-L6140AL2.3, 6 cylinder diesels, 700hp @ 2100 rpm (each) Serial Number: Port: 1401-2567, Stb. 1401-2568

Engine Hours: Port: less then 400 Stb.: less then 400

Transmission: Twin Disk Model: MG5114IV 1.8:1, 14 degree dn. angle; Serial No.: Port: TBD Stb.: TBD

Shafts: 2.75"

 Shaft Seals: PSS Dripless

 Shaft Struts: 1.75 SS316 with 2.75x10" Cuttlas Bearings

Propellers: 30x34" 5 Blade, Katapult

Rope Cutter: Shaft Shark SS700 (2.75")

Performance: 28 knots WOT at 2100rpm (600 gal fuel load)

Fuel Consumption: 26 gph per engine at WOT

Rudder Shafts: 2.5" SS316 with dual cuttlas support and O-Ring seal.

Rudders: Foil Shaped welded SS316 30"x14"

Thru Hull fittings: Marelon, reinforced poly-carbonate

Disclaimer
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.

$
%
$
Disclaimer This calculator is intended solely for general informational purposes, and to provide a rough estimate based on the information you provide. You should not base your decision on this estimate alone.